Guitar Amplifier Tubes or Valves Operation Explained: You will hear people talk about Valve amps and Tube amps. They are the same with the valve being a European term and the tube being used in the USA. From the 1940’s until the 1970’s tubes were used in nearly all electronic devices, such as TV, Radio, Stereo Systems and of course Guitar Amplifiers. With the introduction of low-cost, low-maintenance semiconductor transistor systems, the tube became less desirable for manufacturers and consumers. This allowed for the design of cheaper, smaller and reliable products but cheap is not always best. Most guitarists feel that amplifiers with tubes provide better tone and tone control, when compared with transistor amplification systems.
Tubes amplify or alter sounds by converting heat into electricity. As more electricity is produced, the volume from your loudspeaker increases. A tube is similar to a light-bulb. A glass housing seals the components in a vacuum. The basic components in amplifier tubes are a heating element next to a cathode, a grid, and an anode. The grid separates the cathode from the anode.
The Guitar Pick Up Output Signal
Your guitar pickups send sound out through a cable as a weak electric signal. That signal enters your amplifier and is routed through the tubes. Electricity causes the heating element in the tube to get hot. The heat causes the cathode to release negatively charged electrons. The grid controls the flow of electrons. The various tube grids are controlled by the knobs or dials on the front of your amplifier. The electrons passing through the grid are collected by the anode, and then pass out of the tube. The resulting increased flow of electricity yields an amplified signal from your guitar.
This boosted electric signal, when sent on to the loudspeakers, allows you to hear your guitar at various volume levels. In addition to strict amplification, some amplifier tubes are used to modify your guitar’s signal, resulting in various tones or effects.
You probably noticed that guitar amplifiers with tubes can feel hot, and you can sometimes see an orange-red glow inside. Both are caused by the heating element in the tubes. You can tell power is flowing to a tube when you see this glow, but the glow does not necessarily mean that a tube is working. The cathode, the grid, or the anode may be defective even though the heating element still glows.
The first stage of amplification boosts the input from your guitar only slightly. This is called pre-amplification. The tubes used for pre-amplification produce less energy than the power tubes.
The power tubes are where the real amplification occurs. These pump out large quantities of electricity for driving loudspeakers. You should be able to tell the pre-amp tubes from the power tubes by looking into back of your guitar amplifier. You will see various valves, some small and some larger. The smaller tubes are part of the pre-amplifier stage.
Heater and Standy
Remember that a key component of a tube is the heater, so amplifier tubes have to warm up before they will work. You may have noticed that if you turn on a tube amp and immediately strum your guitar, there is no sound. The heating elements have not warmed the cathode’s yet. Until they do, no amplification takes place. Some amplifiers have a ‘Standby’ mode. When in Standby, the tubes are heated but the output of the amplifier is turned off, effectively muting your system.
Tubes inside amplifiers get VERY hot and produce LETHAL levels of electricity. NEVER handle a hot tube and NEVER reach inside an amplifier that is turned on.
Read our Guitar Amplifier Technology Pages
- Guitar Amplifiers Explained – All Types & Makes
- Valve Amplifier Push-Pull Output Stage Operation Explained
- Valve Amplifier Single Ended Output Stage Explained
- Valve Guitar Amplifier – Output Tubes Explained
- Valve Guitar Amplifier – Pre-Amplifier Tube Operation Explained
- Valve Guitar Amplifier – Technology Explained
- Valve Guitar Amplifier – Tube Amp Basics Explained
- Valve Guitar Amplifier – Tube Maintenance and Care
Also See These Product Listings
- Makes of Guitar Effect Pedals (All the makes like Boss, Dod, EHX etc)
- Types of Guitar Effect Pedal (Overdrive, Fuzz, Delay, Chorus and many more)
- Buy Boutique Guitar Effect Pedals (Custom Made Pedals as used by Famous Guitar Players)
- Makes of Guitar Amplifier (Marshall, Fender, Orange and many more)
- Types of Guitar Amp (Valve, Head, Combo, Solid State, Acoustic etc)
- Buy Boutique Guitar Amplifiers (Custom Made Guitar Amps)
- Buy Guitar Amp Speaker Cabinets
- Replacement Guitar Amp Valves (Single, Matched, Full Kits)
- Guitar Amp Valves Matched Sets (Pairs, Quads, Sextets – Tested and Matched)
- Full Guitar Amp Re-Valve Kits (Change All the Valves)
- Best Deals on Musical Instruments
The YUMAGOLD web site has been created to allow musicians to review and purchase musical related products at the best prices from suppliers on sites like Amazon and Ebay. These are chosen as they have very strict consumer controls to protect the buyer. This web site is constantly expanding and new products are being added daily.