Replacement Valve Kits for BUGERA Guitar Amplifiers


Check out our guitar amplifier Replacement Valve Kits for BUGERA Guitar Amplifiers. These guitar amp valve kits include all of the amp valves that are required to service your valve guitar amplifier and bring it back to peak performance. As the tubes in your guitar amplifier will deteriorate, and the tonal quality be reduced, with the amount of use, it may not be immediately noticeable that your combo tube amp or head tube amp are not performing as well as it was originally designed to.

Replacing all of the valves in your tube amp at the same time will most likely bring your valve guitar amp back to best performance. Especially if you own a practice valve amp where bad tubes will show up quicker due to the low power or a valuable vintage tube amp. You may be tempted to buy a single power valves however this can be a false economy as most, especially higher powered valve amps, need matched sets of amplifier valves to work correctly. If the tubes that are used in the valve guitar amplifier power output circuit are not matched it will cause hum, or noise, and will most likely reduce the life of the other tubes that are in the circuit.

If you are confident on where the problems lie with your tube guitar amplifier then you can decide not to buy a full tube amp set and just buy either the pre-amp valves or the output valve. On the website you can review and buy single pre-amplifier valves, which most likely do not need to be matched, or just buy full sets of matched output tubes if you only want to replace those.

Please ensure you read the installation manual supplied with your guitar amplifier before buying and changing the valves. You can also read our guide to trube amplifier maintenance for some notes on changing and caring for your tubes.

Replacement Valve Kits for BUGERA Guitar Amplifiers.

Review the list below and click on the link to be taken to a page where you can review the prices and buy full guitar amp re-valve sets for your tube guitar amplifier. If your valve amp is not in the list contact us using the link in the top menu and we will add your model to the list

BUGERA Guitar Amplifiers

Bugera is owned by Music Group, a holding company chaired by Uli Behringer, which also owns the Behringer brand. Bugera guitar amplifiers are classed as a boutique design and most bugera guitar amps  are valve guitar amplifiers with a vintage tone and classic design style.

Replacement Valve Kits for Guitar Amplifiers Explained

All head valve guitar amplifiers and combo valve guitar amplifiers include a mixture of pre-amplifier valves, power output valves and rectifier valves (or tubes in the USA). The typical life of a guitar amplifier valve is around 1000 hours. As the valves all operate together the performance of all the valves will degrade over time. If you buy a full guitar amplifier valve kit it will be the best to restore the overall sound quality, performance and reliability of your valve amp to its original state.

These full valve replacement kits that are shown including all of the valves that are required. The valves are fully tested and specially chosen for their sound characteristic and then saved into matched valve sets. The sets include all of the of guitar amp pre-amplifier valves and guitar amp power output valves required. Some kits include the rectifier valve however if this part is required you can buy rectifier valves here.

Why Buy Matched Guitar Amplifier Valves?

Replacement Valve Kits for Guitar Amplifiers
Replacement Valve Kits for Guitar Amplifiers

Most valve combo guitar amps and valve head guitar amps, especially the higher power models and those with push-pull circuit designs, require matched output tubes to operate correctly. Buying one valve and adding it to an existing set will make the amplifier unreliable, cause hum and noise, and reduce the life of the other valves in the circuit, costing a lot more money.

Depending on the design and power output of the amplifier the matched sets are seperated into matched pair valve set (x2 tubes) or matched quad valve set (x4 tubes) and some very high power valve guitar amplifiers can include a matched sextet valve set (x6 tubes). The general rule being more valves more power.

In a push-pull valve guitar amplifier design one valve is pushing the speaker cone out and the other valve is pulling it in, back and forwards, causing sound. To maintain a reliable guitar amplifier performance it is important that the valves push and pull in equal measure. If you buy a matched set of amp valves will mean that the supplier has tested the valves and selected them to have similar characteristics and therefore work together correctly.

Tips on Valve Guitar Amplifier Maintenance

If you are considering doing any valve guitar amplifier maintenance make sure you first read the manufacturers installation booklet for the guitar amplifier you have before buying or changing any of the valves.

One important tip that I have is to monitor how long you have been using the valves. To do this, once you have changed the valves in your guitar amplifier make a note of the date. This can be done by adding a sticker to the back of the amplifier. Taking a view that you use the amp so many hours a week you will be able to decide when is best to change them again in the future, taking into account that guitar amplifier valves (or tubes) will operate under normal conditions for up to 1000 hours, after this they will start to degrade.

Consider these other Pages